Exploring Basic Plumbing When You Install a Bathtub
Exploring Basic Plumbing When You Install a Bathtub
Blog Article
On this page down the page you might get some high-quality content in relation to How to Install a Bathtub.
Setting up a bathtub isn't exactly rocket science, yet it does need solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily obtainable, the project can move immediately; if you need to open a wall to get rid of the old tub and position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will require a helper to vacate the old tub and set in the brand-new one. See to it you have actually qualified yourself for the work and fit attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to consider utilizing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your restroom if you have already purchased a new tub and also do not need to change the plan of your previous water pipelines.
Your tools as well as material checklist need to comprise the following:
Getting ready for the Installment
Firstly, the supporting frame supplied with the bathroom must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps device to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you should do is detach the water. After doing so, turn on the faucets to drain any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little points.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the tub until the spirit level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the appropriate supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the water system and also examine all joints as well as new pipework for leaks as well as tighten them if required. Fill up the bath tub as well as additionally inspect the overflow outlet and also the normal outlet for leakages.
Lastly, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait until the bathtub has been utilized a minimum of once as this will settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Secure the tap in position with the producer offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The former kind must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack a rigid seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, resulting in problems with dampness and possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to permit the activity experienced when the tub remains in use. The sealant can fracture relatively early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on Installing A Bathtub, I think sharing that blog post was a good thing. Remember to take the time to share this post if you appreciated it. Thanks for taking the time to read it.
Don't delay; get expert help. Report this page